I2C GPIO 开漏问题

[xad74]

你好：
最近在用ESP8266的I2C总线驱动外部传感器，SDK版本是1.3，但发现不管发什么数据多无法返回ACK信号，后发现在SDA=1时输出的是高电平信号，而且该信号还无法拉低。外接2K电阻时还是输出3.3V。
后将SDA=1 SCL=1时设置为输入状态，能够采集到ACK信号，我想问下是不是SDK中的开漏模式设置有问题，程序如下：
void ICACHE_FLASH_ATTR
i2c_master_gpio_init(void)
{
ETS_GPIO_INTR_DISABLE() ;
// ETS_INTR_LOCK();

PIN_FUNC_SELECT(I2C_MASTER_SDA_MUX, I2C_MASTER_SDA_FUNC);
PIN_FUNC_SELECT(I2C_MASTER_SCL_MUX, I2C_MASTER_SCL_FUNC);

GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_MASTER_SDA_GPIO)), GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_MASTER_SDA_GPIO))) | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << I2C_MASTER_SDA_GPIO));
GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_MASTER_SCL_GPIO)), GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_MASTER_SCL_GPIO))) | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << I2C_MASTER_SCL_GPIO));

I2C_MASTER_SDA_HIGH_SCL_HIGH();

ETS_GPIO_INTR_ENABLE() ;
// ETS_INTR_UNLOCK();

i2c_master_init();
}
SDA,SCL=1时为输入程序如下
#if Input == 0

#define I2C_MASTER_SDA_HIGH_SCL_HIGH() \
gpio_output_set(1<<I2C_MASTER_SDA_GPIO | 1<<I2C_MASTER_SCL_GPIO, 0, 1<<I2C_MASTER_SDA_GPIO | 1<<I2C_MASTER_SCL_GPIO, 0)
#define I2C_MASTER_SDA_HIGH_SCL_LOW() \
gpio_output_set(1<<I2C_MASTER_SDA_GPIO, 1<<I2C_MASTER_SCL_GPIO, 1<<I2C_MASTER_SDA_GPIO | 1<<I2C_MASTER_SCL_GPIO, 0)
#define I2C_MASTER_SDA_LOW_SCL_HIGH() \
gpio_output_set(1<<I2C_MASTER_SCL_GPIO, 1<<I2C_MASTER_SDA_GPIO, 1<<I2C_MASTER_SDA_GPIO | 1<<I2C_MASTER_SCL_GPIO, 0)

#else
#define I2C_MASTER_SDA_HIGH_SCL_HIGH() \
gpio_output_set(0, 0, 0, 1<<I2C_MASTER_SDA_GPIO | 1<<I2C_MASTER_SCL_GPIO)
#define I2C_MASTER_SDA_HIGH_SCL_LOW() \
gpio_output_set(0, 1<<I2C_MASTER_SCL_GPIO, 1<<I2C_MASTER_SCL_GPIO, 1<<I2C_MASTER_SDA_GPIO)
#define I2C_MASTER_SDA_LOW_SCL_HIGH() \
gpio_output_set(0, 1<<I2C_MASTER_SDA_GPIO, 1<<I2C_MASTER_SDA_GPIO , 1<<I2C_MASTER_SCL_GPIO)

#endif