Yesterday my WAN router died.
I then set up a Raspberry PI as router. I tested it connecting to internet from my laptop through it, and also my mobile gets wifi through it, and everything seems right there.
Then I changed user_config to reflect the change on the mesh devices, and they don't connect.
They don't even try to connect to it, as I can see the connection tries live on the screen attached to the PI and it doesn't show anything when I switch on the mesh devices.
This is the serial log of a device. It always ends up in a "enable mesh fail, re-enable" and goes on scanning (on channel 0?). I don't know, but I think it should scan all channels.
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:07:d5) + softAP(5e:cf:7f:c1:07:d5)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
This is another device that has the PI router in range:
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:07:d5) + softAP(5e:cf:7f:c1:07:d5)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
This is user_config.h. I changed the server_ip, the MESH_ROUTER_BSSID, ROUTER_SSID and ROUTER_PASS. Also there is no server at this time at that address, but the devices don't get a wifi connection, I don't think they will ask for the server yet.
static const uint16_t server_port = 7000; /*PORT USED BY USER IOT SERVER FOR MESH SERVICE*/
static const uint8_t server_ip[4] = {192, 168, 10, 1}; /*USER IOT SERVER IP ADDRESS*/
static const uint32_t UART_BAUT_RATIO = 115200; /*UART BAUT RATIO*/
static const uint8_t MESH_GROUP_ID[6] = {0x18,0xfe,0x34,0x00,0x00,0x50}; /*MESH_GROUP_ID & MESH_SSID_PREFIX REPRESENTS ONE MESH NETWORK*/
//static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x80, 0x5A, 0x5B, 0x1B, 0xAD};
/*MAC OF ROUTER*/
static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x0B, 0x81, 0x88, 0x63, 0x83};
/*
* please change MESH_ROUTER_SSID and MESH_ROUTER_PASSWD according to your router
*/
#define MESH_ROUTER_SSID "PitAP" /*THE ROUTER SSID*/
#define MESH_ROUTER_PASSWD "*8*8*8*8*8*8*8*" /*THE ROUTER PASSWORD*/
#define MESH_SSID_PREFIX "MEMO" /*SET THE DEFAULT MESH SSID PREFIX;THE FINAL SSID OF SOFTAP WOULD BE "MESH_SSID_PREFIX_X_YYYYYY"*/
#define MESH_AUTH AUTH_WPA2_PSK /*AUTH_MODE OF SOFTAP FOR EACH MESH NODE*/
#define MESH_PASSWD "3HappyLions" /*SET PASSWORD OF SOFTAP FOR EACH MESH NODE*/
#define MESH_MAX_HOP (4) /*MAX_HOPS OF MESH NETWORK*/
Can't connect to ap from devices
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
-
ESP_Alen
Re: Can't connect to ap from devices
Postby ESP_Alen » Thu Sep 29, 2016 1:02 pm
traderlopez wrote:Yesterday my WAN router died.
I then set up a Raspberry PI as router. I tested it connecting to internet from my laptop through it, and also my mobile gets wifi through it, and everything seems right there.
Then I changed user_config to reflect the change on the mesh devices, and they don't connect.
They don't even try to connect to it, as I can see the connection tries live on the screen attached to the PI and it doesn't show anything when I switch on the mesh devices.
This is the serial log of a device. It always ends up in a "enable mesh fail, re-enable" and goes on scanning (on channel 0?). I don't know, but I think it should scan all channels.
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:07:d5) + softAP(5e:cf:7f:c1:07:d5)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
This is another device that has the PI router in range:
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:07:d5) + softAP(5e:cf:7f:c1:07:d5)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
This is user_config.h. I changed the server_ip, the MESH_ROUTER_BSSID, ROUTER_SSID and ROUTER_PASS. Also there is no server at this time at that address, but the devices don't get a wifi connection, I don't think they will ask for the server yet.
static const uint16_t server_port = 7000; /*PORT USED BY USER IOT SERVER FOR MESH SERVICE*/
static const uint8_t server_ip[4] = {192, 168, 10, 1}; /*USER IOT SERVER IP ADDRESS*/
static const uint32_t UART_BAUT_RATIO = 115200; /*UART BAUT RATIO*/
static const uint8_t MESH_GROUP_ID[6] = {0x18,0xfe,0x34,0x00,0x00,0x50}; /*MESH_GROUP_ID & MESH_SSID_PREFIX REPRESENTS ONE MESH NETWORK*/
//static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x80, 0x5A, 0x5B, 0x1B, 0xAD};
/*MAC OF ROUTER*/
static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x0B, 0x81, 0x88, 0x63, 0x83};
/*
* please change MESH_ROUTER_SSID and MESH_ROUTER_PASSWD according to your router
*/
#define MESH_ROUTER_SSID "PitAP" /*THE ROUTER SSID*/
#define MESH_ROUTER_PASSWD "*8*8*8*8*8*8*8*" /*THE ROUTER PASSWORD*/
#define MESH_SSID_PREFIX "MEMO" /*SET THE DEFAULT MESH SSID PREFIX;THE FINAL SSID OF SOFTAP WOULD BE "MESH_SSID_PREFIX_X_YYYYYY"*/
#define MESH_AUTH AUTH_WPA2_PSK /*AUTH_MODE OF SOFTAP FOR EACH MESH NODE*/
#define MESH_PASSWD "3HappyLions" /*SET PASSWORD OF SOFTAP FOR EACH MESH NODE*/
#define MESH_MAX_HOP (4) /*MAX_HOPS OF MESH NETWORK*/
The router ssid is different from "PitAP", please pay attention to statement with red color.
Please use scenario of mesh_performance, and modify user_config.h in mesh_performance/include
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
Re: Can't connect to ap from devices
Postby traderlopez » Thu Sep 29, 2016 2:47 pm
I can't find out how to switch scenarios.
I run gen_misc.sh from the mesh_demo folder. I check the timestamp of the output files being saved in the flash and the update file has the correct updated date. I don't understand how the performance scenario folder user_config.h can have some influence on the demo files I changed in the demo folder.
If it is possible, please explain me as shortly as you wish how to switch scenarios between demo and performance.
Thanks very much.
I run gen_misc.sh from the mesh_demo folder. I check the timestamp of the output files being saved in the flash and the update file has the correct updated date. I don't understand how the performance scenario folder user_config.h can have some influence on the demo files I changed in the demo folder.
If it is possible, please explain me as shortly as you wish how to switch scenarios between demo and performance.
Thanks very much.
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
Re: Can't connect to ap from devices
Postby traderlopez » Thu Sep 29, 2016 3:17 pm
It seems that the problem is related to ESP-TOUCH, which I don't use
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
Those ssid and pwd can't be known as there is no ESP-TOUCH enabled mobile phones in range.
Can I get rid of ESP-TOUCH in the Mesh?
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
Those ssid and pwd can't be known as there is no ESP-TOUCH enabled mobile phones in range.
Can I get rid of ESP-TOUCH in the Mesh?
Re: Can't connect to ap from devices
Postby trojek » Thu Sep 29, 2016 3:46 pm
I'm absolutely beginner at esp8266 but I think that your problems is here:
. In my case it looks: flush ssid:SSID_NAME pwd:PASSWORD. In you case it looks like you don't have any ssid and your password is "strange". I have password in plain text.flush ssid: pwd:@úÿ?@úÿ?
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
Re: Can't connect to ap from devices
Postby traderlopez » Thu Sep 29, 2016 4:47 pm
Hi trojek,
If you've set a mobile device for ESP-TOUCH, you forgot to change SSID and PASSWORD to useful values, in the code, so you are seeing the default values.
The values I am being informed are not real, they are rubbish from memory, as they haven't been initialized before they appear logged in the serial port
Thanks very much.
If you've set a mobile device for ESP-TOUCH, you forgot to change SSID and PASSWORD to useful values, in the code, so you are seeing the default values.
The values I am being informed are not real, they are rubbish from memory, as they haven't been initialized before they appear logged in the serial port
Thanks very much.
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
Re: Can't connect to ap from devices
Postby traderlopez » Thu Sep 29, 2016 5:17 pm
Finally I got the router up again and running.
I tried to connect the mesh devices and it happens the same.
It wasn't the raspberry pi routing thing, it has something else.
The server is connected, although I think this doesn't make any difference.
This time the user_config.h is:
static const uint16_t server_port = 7000; /*PORT USED BY USER IOT SERVER FOR MESH SERVICE*/
static const uint8_t server_ip[4] = {192, 168, 0, 100}; /*USER IOT SERVER IP ADDRESS*/
static const uint32_t UART_BAUT_RATIO = 115200; /*UART BAUT RATIO*/
static const uint8_t MESH_GROUP_ID[6] = {0x18,0xfe,0x34,0x00,0x00,0x50}; /*MESH_GROUP_ID & MESH_SSID_PREFIX REPRESENTS ONE MESH NETWORK*/
static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x80, 0x5A, 0x5B, 0x1B, 0xAD};
/*MAC OF ROUTER*/
//static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x0B, 0x81, 0x88, 0x63, 0x83}; PI - no va
/*
* please change MESH_ROUTER_SSID and MESH_ROUTER_PASSWD according to your router
*/
#define MESH_ROUTER_SSID "NETDEA" /*THE ROUTER SSID*/
#define MESH_ROUTER_PASSWD "rinocero" /*THE ROUTER PASSWORD*/
#define MESH_SSID_PREFIX "DEMOMESA" /*SET THE DEFAULT MESH SSID PREFIX;THE FINAL SSID OF SOFTAP WOULD BE "MESH_SSID_PREFIX_X_YYYYYY"*/
#define MESH_AUTH AUTH_WPA2_PSK /*AUTH_MODE OF SOFTAP FOR EACH MESH NODE*/
#define MESH_PASSWD "amiantos" /*SET PASSWORD OF SOFTAP FOR EACH MESH NODE*/
#define MESH_MAX_HOP (4) /*MAX_HOPS OF MESH NETWORK*/
And a random device log:
{lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:0b:64)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:0b:64) + softAP(5e:cf:7f:c1:0b:64)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
I tried to connect the mesh devices and it happens the same.
It wasn't the raspberry pi routing thing, it has something else.
The server is connected, although I think this doesn't make any difference.
This time the user_config.h is:
static const uint16_t server_port = 7000; /*PORT USED BY USER IOT SERVER FOR MESH SERVICE*/
static const uint8_t server_ip[4] = {192, 168, 0, 100}; /*USER IOT SERVER IP ADDRESS*/
static const uint32_t UART_BAUT_RATIO = 115200; /*UART BAUT RATIO*/
static const uint8_t MESH_GROUP_ID[6] = {0x18,0xfe,0x34,0x00,0x00,0x50}; /*MESH_GROUP_ID & MESH_SSID_PREFIX REPRESENTS ONE MESH NETWORK*/
static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x80, 0x5A, 0x5B, 0x1B, 0xAD};
/*MAC OF ROUTER*/
//static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x0B, 0x81, 0x88, 0x63, 0x83}; PI - no va
/*
* please change MESH_ROUTER_SSID and MESH_ROUTER_PASSWD according to your router
*/
#define MESH_ROUTER_SSID "NETDEA" /*THE ROUTER SSID*/
#define MESH_ROUTER_PASSWD "rinocero" /*THE ROUTER PASSWORD*/
#define MESH_SSID_PREFIX "DEMOMESA" /*SET THE DEFAULT MESH SSID PREFIX;THE FINAL SSID OF SOFTAP WOULD BE "MESH_SSID_PREFIX_X_YYYYYY"*/
#define MESH_AUTH AUTH_WPA2_PSK /*AUTH_MODE OF SOFTAP FOR EACH MESH NODE*/
#define MESH_PASSWD "amiantos" /*SET PASSWORD OF SOFTAP FOR EACH MESH NODE*/
#define MESH_MAX_HOP (4) /*MAX_HOPS OF MESH NETWORK*/
And a random device log:
{lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:0b:64)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:0b:64) + softAP(5e:cf:7f:c1:0b:64)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
-
ESP_Alen
Re: Can't connect to ap from devices
Postby ESP_Alen » Thu Sep 29, 2016 5:37 pm
traderlopez wrote:It seems that the problem is related to ESP-TOUCH, which I don't use
;lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:07:d5)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
Those ssid and pwd can't be known as there is no ESP-TOUCH enabled mobile phones in range.
Can I get rid of ESP-TOUCH in the Mesh?
Yes, if you don't need eep-touch, please disable esp-touch.
-
ESP_Alen
Re: Can't connect to ap from devices
Postby ESP_Alen » Thu Sep 29, 2016 5:48 pm
traderlopez wrote:Finally I got the router up again and running.
I tried to connect the mesh devices and it happens the same.
It wasn't the raspberry pi routing thing, it has something else.
The server is connected, although I think this doesn't make any difference.
This time the user_config.h is:
static const uint16_t server_port = 7000; /*PORT USED BY USER IOT SERVER FOR MESH SERVICE*/
static const uint8_t server_ip[4] = {192, 168, 0, 100}; /*USER IOT SERVER IP ADDRESS*/
static const uint32_t UART_BAUT_RATIO = 115200; /*UART BAUT RATIO*/
static const uint8_t MESH_GROUP_ID[6] = {0x18,0xfe,0x34,0x00,0x00,0x50}; /*MESH_GROUP_ID & MESH_SSID_PREFIX REPRESENTS ONE MESH NETWORK*/
static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x80, 0x5A, 0x5B, 0x1B, 0xAD};
/*MAC OF ROUTER*/
//static const uint8_t MESH_ROUTER_BSSID[6] = {0x00, 0x0B, 0x81, 0x88, 0x63, 0x83}; PI - no va
/*
* please change MESH_ROUTER_SSID and MESH_ROUTER_PASSWD according to your router
*/
#define MESH_ROUTER_SSID "NETDEA" /*THE ROUTER SSID*/
#define MESH_ROUTER_PASSWD "rinocero" /*THE ROUTER PASSWORD*/
#define MESH_SSID_PREFIX "DEMOMESA" /*SET THE DEFAULT MESH SSID PREFIX;THE FINAL SSID OF SOFTAP WOULD BE "MESH_SSID_PREFIX_X_YYYYYY"*/
#define MESH_AUTH AUTH_WPA2_PSK /*AUTH_MODE OF SOFTAP FOR EACH MESH NODE*/
#define MESH_PASSWD "amiantos" /*SET PASSWORD OF SOFTAP FOR EACH MESH NODE*/
#define MESH_MAX_HOP (4) /*MAX_HOPS OF MESH NETWORK*/
And a random device log:
{lESP-TOUCH FLOW INIT...
ESP-TOUCH SET STATION MODE ...
SC version: V2.5.4
flush ssid: pwd:@úÿ?@úÿ?
mesh version: v1.3.2
mode : sta(5c:cf:7f:c1:0b:64)
add if0
scandone
err,scan status 1
scandone
err,scan status 4
ESP-TOUCH TIMEOUT
mode : sta(5c:cf:7f:c1:0b:64) + softAP(5e:cf:7f:c1:0b:64)
add if1
dhcp server start:(ip:192.168.4.1,mask:255.255.255.0,gw:192.168.4.1)
bcn 100
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
scan-ch:0
scandone
scan-ch:0
scandone
no ap to join
mesh_enable_cb
enable mesh fail, re-enable
scan-ch:0
scandone
If you want to switch router, please use eep-touch to push new AP to device.
-
traderlopez
- Posts: 20
- Joined: Thu Sep 22, 2016 12:55 pm
Re: Can't connect to ap from devices
Postby traderlopez » Thu Sep 29, 2016 6:01 pm
There must be some other way to set the router information into the devices, at least from the programming point of view. I have them on the table, not in my clients offices. I still can program them with other data.
Please tell me another way to get the new router information programmed into the flash. Currently I use user_config.h.
Thanks very much in advance.
Please tell me another way to get the new router information programmed into the flash. Currently I use user_config.h.
Thanks very much in advance.
Who is online
Users browsing this forum: No registered users and 57 guests
Login
Newbies Start Here
Are you new to ESP8266?
Unsure what to do?
Dunno where to start?
Start right here!
Latest SDK
Documentation
Complete listing of the official ESP8266 related documentation release by ESPRESSIF!
Must read here!
- All times are UTC+08:00
- Top
- Delete all board cookies
About Us
Espressif Systems is a fabless semiconductor company providing cutting-edge low power WiFi SoCs and wireless solutions for wireless communications and Internet of Things applications. We are the manufacturer of ESP8266EX.