ESP8266 Developer Zone The Official ESP8266 Forum 2016-09-05T13:45:03+08:00 https://bbs.espressif.com:443/feed.php?f=7&t=49 2016-09-05T13:45:03+08:00 2016-09-05T13:45:03+08:00 https://bbs.espressif.com:443/viewtopic.php?t=49&p=9733#p9733 <![CDATA[Re: A first order sigma-delta signal from io pin source]]> slove this problem i edit code
its work :D

Code:


/*
/******************************************************************************
 * MODULEName : set_sigma MODULE

EACH PIN CAN CONNET TO A SIGMA-DELTA , ALL PINS SHEARS THE SAME SIGMA-DELTA SOURCE.

THE TARGET DUTY AND FREQUENCY CAN BE MODIFIED VIA THE REG ADDR GPIO_SIGMA_DELTA

THE TARGET FREQUENCY IS DEFINED AS:

FREQ = 80,000,000/prescale * target /256  HZ,     0<target<128
FREQ = 80,000,000/prescale * (256-target) /256  HZ,     128<target<256
target: duty ,0-255
prescale: clk_div,0-255
so the target and prescale will both affect the freq.


YOU CAN DO THE TEST LIKE THIS:
1. INIT :  sigma_delta_setup(PERIPHS_IO_MUX_MTDI_U,12,FUNC_GPIO12);
2. USE 312K:   set_sigma_duty_312KHz(2);
OR 2. SET VAL:  set_sigma_target(uint8 target) AND  set_sigma_prescale

3. DEINIT AND DISABLE: sigma_delta_close(uint32 GPIO_NUM), eg.sigma_delta_close(2)

*******************************************************************************/



#include "osapi.h"
#include "c_types.h"
#include "ets_sys.h"
#include "eagle_soc.h"
#include "gpio.h"
#include "esp8266.h"


//uint32 GPIO_SIGMA_DELTA_NUM=0x68;

#define GPIO_SIGMA_DELTA_NUM  0x68
 // modify for pin

#define GPIO_SIGMA_DELTA      0x68  //defined in gpio register.xls


#define   PERIPHS_GPIO_BASEADDR   0x60000300
#define GPIO_PIN_ADDR(i)    (GPIO_PIN0_ADDRESS + i*4)
#define GPIO_SIGMA_DELTA_ADDRESS   (PERIPHS_GPIO_BASEADDR + 0x68)  //defined in gpio register.xls


#define GPIO_SIGMA_DELTA_SETTING_MASK  (0x00000001ff)

#define GPIO_SIGMA_DELTA_ENABLE  1
#define GPIO_SIGMA_DELTA_DISABLE   (~GPIO_SIGMA_DELTA_ENABLE)
#define GPIO_SIGMA_DELTA_MSB                     16
#define GPIO_SIGMA_DELTA_LSB                      16
#define GPIO_SIGMA_DELTA_MASK                  (0x00000001<<GPIO_SIGMA_DELTA_LSB)
#define GPIO_SIGMA_DELTA_GET(x)                 (((x) & GPIO_SIGMA_DELTA_MASK) >> GPIO_SIGMA_DELTA_LSB)
#define GPIO_SIGMA_DELTA_SET(x)                  (((x) << GPIO_SIGMA_DELTA_LSB) & GPIO_SIGMA_DELTA_MASK)


#define GPIO_SIGMA_DELTA_TARGET_MSB  7
#define GPIO_SIGMA_DELTA_TARGET_LSB  0
#define GPIO_SIGMA_DELTA_TARGET_MASK                  (0x000000FF<<GPIO_SIGMA_DELTA_TARGET_LSB)
#define GPIO_SIGMA_DELTA_TARGET_GET(x)                 (((x) & GPIO_SIGMA_DELTA_TARGET_MASK) >> GPIO_SIGMA_DELTA_TARGET_LSB)
#define GPIO_SIGMA_DELTA_TARGET_SET(x)                  (((x) << GPIO_SIGMA_DELTA_TARGET_LSB) & GPIO_SIGMA_DELTA_TARGET_MASK)


#define GPIO_SIGMA_DELTA_PRESCALE_MSB  15
#define GPIO_SIGMA_DELTA_PRESCALE_LSB  8
#define GPIO_SIGMA_DELTA_PRESCALE_MASK  (0x000000FF<<GPIO_SIGMA_DELTA_PRESCALE_LSB)
#define GPIO_SIGMA_DELTA_PRESCALE_GET(x)                 (((x) & GPIO_SIGMA_DELTA_PRESCALE_MASK) >> GPIO_SIGMA_DELTA_PRESCALE_LSB)
#define GPIO_SIGMA_DELTA_PRESCALE_SET(x)                  (((x) << GPIO_SIGMA_DELTA_PRESCALE_LSB) & GPIO_SIGMA_DELTA_PRESCALE_MASK)


/******************************************************************************
 * FunctionName : sigma_delta_setup
 * Description  : Init Pin Config for Sigma_delta , change pin source to sigma-delta
 * Parameters   : uint32 GPIO_MUX, GPIO MUX REG ,DEFINED IN EAGLE_SOC.H, e.g.: PERIPHS_IO_MUX_MTCK_U
        uint32 GPIO_NUM, GPIO NUM ACCORDING TO THE MUX NUM , e.g.: 13 for MTCK
        uint32 GPIO_FUNC, GPIO PIN FUNC , DEFINED IN EAGLE_SOC.H , e.g.: FUNC_GPIO13
 * Returns      : none
*******************************************************************************/



void ICACHE_FLASH_ATTR
sigma_delta_setup(uint32 GPIO_MUX,uint32 GPIO_NUM,uint32 GPIO_FUNC)
{
//GPIO_SIGMA_DELTA_NUM= 0x68;//GPIO_NUM;
  uint32 pinaddr = GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM));


    //============================================================================
    //STEP 1: SIGMA-DELTA CONFIG;REG SETUP
/*
    GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
       (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM)))
        &(~GPIO_SIGMA_DELTA_SETTING_MASK))|
       GPIO_SIGMA_DELTA_SET(GPIO_SIGMA_DELTA_ENABLE)|
        GPIO_SIGMA_DELTA_TARGET_SET(0x00)|
         GPIO_SIGMA_DELTA_PRESCALE_SET(0x00) );
*/
    //============================================================================

    //STEP 2: PIN FUNC CONFIG :SET PIN TO GPIO MODE AND ENABLE OUTPUT
  //  PIN_FUNC_SELECT(GPIO_MUX, GPIO_FUNC);
  //  gpio_output_set(0,0,0x1<<GPIO_NUM,0);

   //gpio_output_set(1<<GPIO_NUM,0,1<<GPIO_NUM,0);
    //============================================================================

    //STEP 3: CONNECT SIGNAL TO GPIO PAD
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)),
         GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)))|
       GPIO_PIN_SOURCE_SET(  SIGMA_AS_PIN_SOURCE )  );
    //============================================================================
    //ets_printf("test reg gpio mtdi : 0x%08x \n",GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM))));

   gpio_output_set(1<<GPIO_NUM,0,1<<GPIO_NUM,0);

   // Make it output PWM signal
  GPIO_REG_WRITE(pinaddr, GPIO_REG_READ(pinaddr) | 1);

   GPIO_REG_WRITE(GPIO_SIGMA_DELTA, 0x1FFFF);
}




/******************************************************************************
 * FunctionName : sigma_delta_close
 * Description  : DEinit Pin ,from Sigma_delta mode to GPIO input mode
 * Parameters   : uint32 GPIO_NUM, GPIO NUM ACCORDING TO THE MUX NUM , e.g.: 13 for MTCK
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    sigma_delta_close(uint32 GPIO_NUM)
{

    //============================================================================
    //STEP 1: SIGMA-DELTA DEINIT
    GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
           (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))) &(~GPIO_SIGMA_DELTA_SETTING_MASK))|
             GPIO_SIGMA_DELTA_SET(GPIO_SIGMA_DELTA_DISABLE)|
                GPIO_SIGMA_DELTA_TARGET_SET(0x00)|
                     GPIO_SIGMA_DELTA_PRESCALE_SET(0x00) );

    //ets_printf("test reg gpio sigma : 0x%08x \n",GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))));
    //============================================================================

    //STEP 2: GPIO OUTPUT DISABLE
    //gpio_output_set(0,0,0,0x1<<GPIO_NUM);
    //============================================================================

    //STEP 3: CONNECT GPIO TO PIN PAD
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)),
            GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)))|
              GPIO_PIN_SOURCE_SET(  GPIO_AS_PIN_SOURCE )       );
    //============================================================================


}



/******************************************************************************
 * FunctionName : set_sigma_target
 * Description  : SET TARGET DUTY FOR SIGMA-DELTA
 * Parameters   : uint8 target, DUTY NUM , 1BYTE , DUTY RANGE : 0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_target(uint8 target)
{
    uint32 reg_r;
    //uint32 t_tar=target;
    //set sigma signal duty target
/*
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
       (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM)))
        &(~GPIO_SIGMA_DELTA_TARGET_MASK))|
        GPIO_SIGMA_DELTA_TARGET_SET(target));

   */
        reg_r=GPIO_REG_READ(GPIO_SIGMA_DELTA);
        reg_r= reg_r & 0xFFFFFF00 ;
        reg_r= reg_r|target;
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA, reg_r);

}



/******************************************************************************
 * FunctionName : set_sigma_prescale
 * Description  : SET SIGMA-DELTA SIGNAL CLK PRESCALE(CLE_DIV)
 * Parameters   : uint8 prescale, CLK_DIV , 0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_prescale(uint8 prescale)
{
    uint32 reg_r;
     uint16 p_r=prescale;
    //set sigma signal clk prescale(clk div)
/*
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
           (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM)))
            &(~GPIO_SIGMA_DELTA_PRESCALE_MASK))|
           GPIO_SIGMA_DELTA_PRESCALE_SET(prescale) );

*/
        reg_r=GPIO_REG_READ(GPIO_SIGMA_DELTA);
        reg_r= reg_r & 0xFFFF00FF ;
        reg_r= reg_r|( p_r<<8);
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA, reg_r);

}



/******************************************************************************
 * FunctionName : set_sigma_duty_312KHz
 * Description  : 312K CONFIG EXAMPLE
 * Parameters   : uint8 duty, TARGET DUTY FOR 312K,  0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_duty_312KHz(uint8 duty)
{

    uint8 target = 0,prescale=0;
    target = (duty>128)?(256-duty):duty;
    prescale = (target==0)?0:(target-1);

    //freq = 80000 (khz) /256 /duty_target * (prescale+1)
    set_sigma_target(duty);//SET DUTY TARGET
    set_sigma_prescale(prescale);//SET CLK DIV

}


   uint32 relaystate=1;

void ICACHE_FLASH_ATTR relay_set(int on) {
  uint32 pin = 4;
  uint32 pinaddr = GPIO_PIN_ADDR(GPIO_ID_PIN(pin));
 uint32 GPIO_NUM=pin;
  // Make pin a GPIO pin
  GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)),
            GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)))|
              GPIO_PIN_SOURCE_SET(  GPIO_AS_PIN_SOURCE )  );
  // Set to H (Transistor off)
  gpio_output_set(1<<pin,0,1<<pin,0);



  // Make it output PWM signal
  GPIO_REG_WRITE(pinaddr, GPIO_REG_READ(pinaddr) | 1);

  // Value for 12.7V
  GPIO_REG_WRITE(GPIO_SIGMA_DELTA, 0x1FFFF);


}



























Statistics: Posted by hadipic — Mon Sep 05, 2016 1:45 pm

]]> 2016-08-19T21:31:59+08:00 2016-08-19T21:31:59+08:00 https://bbs.espressif.com:443/viewtopic.php?t=49&p=8590#p8590 <![CDATA[Re: A first order sigma-delta signal from io pin source]]> i have a qution
what (GPIO_SIGMA_DELTA_NUM) ?
i define
#define GPIO_SIGMA_DELTA_NUM 4 // modify for pin
for gpio4 but not output signal
help me

Statistics: Posted by hadipic — Fri Aug 19, 2016 9:31 pm

]]> 2014-11-18T02:59:26+08:00 2014-11-18T02:59:26+08:00 https://bbs.espressif.com:443/viewtopic.php?t=49&p=174#p174 <![CDATA[A first order sigma-delta signal from io pin source]]> * MODULEName : set_sigma MODULE

A first order sigma-delta is just like a pwm signal.

EACH PIN CAN CONNET TO A SIGMA-DELTA , ALL PINS SHEARS THE SAME SIGMA-DELTA SOURCE.

THE TARGET DUTY AND FREQUENCY CAN BE MODIFIED VIA THE REG ADDR GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))

THE TARGET FREQUENCY IS DEFINED AS:

FREQ = 80,000,000/prescale * target /256 HZ, 0<target<128
FREQ = 80,000,000/prescale * (256-target) /256 HZ, 128<target<256
target: duty ,0-255
prescale: clk_div,0-255
so the target and prescale will both affect the freq.


YOU CAN DO THE TEST LIKE THIS:
1. INIT : sigma_delta_setup(PERIPHS_IO_MUX_MTDI_U,12,FUNC_GPIO12);
2. USE 312K: set_sigma_duty_312KHz(2);
OR 2. SET VAL: set_sigma_target(uint8 target) AND set_sigma_prescale

3. DE-INIT AND DISABLE: sigma_delta_close(uint32 GPIO_NUM), eg.sigma_delta_close(2)

*******************************************************************************/
*/

Code:

/*
/******************************************************************************
 * MODULEName : set_sigma MODULE

EACH PIN CAN CONNET TO A SIGMA-DELTA , ALL PINS SHEARS THE SAME SIGMA-DELTA SOURCE.

THE TARGET DUTY AND FREQUENCY CAN BE MODIFIED VIA THE REG ADDR GPIO_SIGMA_DELTA

THE TARGET FREQUENCY IS DEFINED AS:

FREQ = 80,000,000/prescale * target /256  HZ,     0<target<128
FREQ = 80,000,000/prescale * (256-target) /256  HZ,     128<target<256
target: duty ,0-255
prescale: clk_div,0-255
so the target and prescale will both affect the freq.


YOU CAN DO THE TEST LIKE THIS:
1. INIT :  sigma_delta_setup(PERIPHS_IO_MUX_MTDI_U,12,FUNC_GPIO12);
2. USE 312K:   set_sigma_duty_312KHz(2);
OR 2. SET VAL:  set_sigma_target(uint8 target) AND  set_sigma_prescale

3. DEINIT AND DISABLE: sigma_delta_close(uint32 GPIO_NUM), eg.sigma_delta_close(2)

*******************************************************************************/



#include "osapi.h"
#include "c_types.h"
#include "ets_sys.h"
#include "eagle_soc.h"
#include "gpio.h"




#define GPIO_PIN_ADDR(i) (GPIO_PIN0_ADDRESS + i*4)
#define GPIO_SIGMA_DELTA      0x60000368  //defined in gpio register.xls

#define GPIO_SIGMA_DELTA_SETTING_MASK  (0x00000001ff)

#define GPIO_SIGMA_DELTA_ENABLE  1
#define GPIO_SIGMA_DELTA_DISABLE   (~GPIO_SIGMA_DELTA_ENABLE)
#define GPIO_SIGMA_DELTA_MSB                     16
#define GPIO_SIGMA_DELTA_LSB                      16
#define GPIO_SIGMA_DELTA_MASK                  (0x00000001<<GPIO_SIGMA_DELTA_LSB)
#define GPIO_SIGMA_DELTA_GET(x)                 (((x) & GPIO_SIGMA_DELTA_MASK) >> GPIO_SIGMA_DELTA_LSB)
#define GPIO_SIGMA_DELTA_SET(x)                  (((x) << GPIO_SIGMA_DELTA_LSB) & GPIO_SIGMA_DELTA_MASK)


#define GPIO_SIGMA_DELTA_TARGET_MSB  7
#define GPIO_SIGMA_DELTA_TARGET_LSB  0
#define GPIO_SIGMA_DELTA_TARGET_MASK                  (0x000000FF<<GPIO_SIGMA_DELTA_TARGET_LSB)
#define GPIO_SIGMA_DELTA_TARGET_GET(x)                 (((x) & GPIO_SIGMA_DELTA_TARGET_MASK) >> GPIO_SIGMA_DELTA_TARGET_LSB)
#define GPIO_SIGMA_DELTA_TARGET_SET(x)                  (((x) << GPIO_SIGMA_DELTA_TARGET_LSB) & GPIO_SIGMA_DELTA_TARGET_MASK)


#define GPIO_SIGMA_DELTA_PRESCALE_MSB  15
#define GPIO_SIGMA_DELTA_PRESCALE_LSB  8
#define GPIO_SIGMA_DELTA_PRESCALE_MASK  (0x000000FF<<GPIO_SIGMA_DELTA_PRESCALE_LSB)
#define GPIO_SIGMA_DELTA_PRESCALE_GET(x)                 (((x) & GPIO_SIGMA_DELTA_PRESCALE_MASK) >> GPIO_SIGMA_DELTA_PRESCALE_LSB)
#define GPIO_SIGMA_DELTA_PRESCALE_SET(x)                  (((x) << GPIO_SIGMA_DELTA_PRESCALE_LSB) & GPIO_SIGMA_DELTA_PRESCALE_MASK)


/******************************************************************************
 * FunctionName : sigma_delta_setup
 * Description  : Init Pin Config for Sigma_delta , change pin source to sigma-delta
 * Parameters   : uint32 GPIO_MUX, GPIO MUX REG ,DEFINED IN EAGLE_SOC.H, e.g.: PERIPHS_IO_MUX_MTCK_U
        uint32 GPIO_NUM, GPIO NUM ACCORDING TO THE MUX NUM , e.g.: 13 for MTCK
        uint32 GPIO_FUNC, GPIO PIN FUNC , DEFINED IN EAGLE_SOC.H , e.g.: FUNC_GPIO13
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
sigma_delta_setup(uint32 GPIO_MUX,uint32 GPIO_NUM,uint32 GPIO_FUNC)
{
    //============================================================================
    //STEP 1: SIGMA-DELTA CONFIG;REG SETUP
    GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
                                                        (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))) &(~GPIO_SIGMA_DELTA_SETTING_MASK))|
                                                          GPIO_SIGMA_DELTA_SET(GPIO_SIGMA_DELTA_ENABLE)|
                                                          GPIO_SIGMA_DELTA_TARGET_SET(0x00)|
                                                          GPIO_SIGMA_DELTA_PRESCALE_SET(0x00) );

    //============================================================================

    //STEP 2: PIN FUNC CONFIG :SET PIN TO GPIO MODE AND ENABLE OUTPUT
    PIN_FUNC_SELECT(GPIO_MUX, GPIO_FUNC);
    gpio_output_set(0,0,0x1<<GPIO_NUM,0);
   
    //============================================================================

    //STEP 3: CONNECT SIGNAL TO GPIO PAD
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)),       
                                                            GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)))|
                                                            GPIO_PIN_SOURCE_SET(  SIGMA_AS_PIN_SOURCE )                     );                                                                                   
    //============================================================================
    //ets_printf("test reg gpio mtdi : 0x%08x \n",GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM))));

}




/******************************************************************************
 * FunctionName : sigma_delta_close
 * Description  : DEinit Pin ,from Sigma_delta mode to GPIO input mode
 * Parameters   : uint32 GPIO_NUM, GPIO NUM ACCORDING TO THE MUX NUM , e.g.: 13 for MTCK
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    sigma_delta_close(uint32 GPIO_NUM)
{

    //============================================================================
    //STEP 1: SIGMA-DELTA DEINIT
    GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
                                                        (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))) &(~GPIO_SIGMA_DELTA_SETTING_MASK))|
                                                          GPIO_SIGMA_DELTA_SET(GPIO_SIGMA_DELTA_DISABLE)|
                                                          GPIO_SIGMA_DELTA_TARGET_SET(0x00)|
                                                          GPIO_SIGMA_DELTA_PRESCALE_SET(0x00) );

    //ets_printf("test reg gpio sigma : 0x%08x \n",GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))));
    //============================================================================

    //STEP 2: GPIO OUTPUT DISABLE
    gpio_output_set(0,0,0,0x1<<GPIO_NUM);
    //============================================================================

    //STEP 3: CONNECT GPIO TO PIN PAD
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)),       
                                                            GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_NUM)))|
                                                            GPIO_PIN_SOURCE_SET(  GPIO_AS_PIN_SOURCE )                     );                                                                                   
    //============================================================================

}



/******************************************************************************
 * FunctionName : set_sigma_target
 * Description  : SET TARGET DUTY FOR SIGMA-DELTA
 * Parameters   : uint8 target, DUTY NUM , 1BYTE , DUTY RANGE : 0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_target(uint8 target)
{
    //set sigma signal duty target
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
                                                        (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))) &(~GPIO_SIGMA_DELTA_TARGET_MASK))|
                                                          GPIO_SIGMA_DELTA_TARGET_SET(target));
}



/******************************************************************************
 * FunctionName : set_sigma_prescale
 * Description  : SET SIGMA-DELTA SIGNAL CLK PRESCALE(CLE_DIV)
 * Parameters   : uint8 prescale, CLK_DIV , 0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_prescale(uint8 prescale)
{
    //set sigma signal clk prescale(clk div)
        GPIO_REG_WRITE(GPIO_SIGMA_DELTA,
                                                        (GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(GPIO_SIGMA_DELTA_NUM))) &(~GPIO_SIGMA_DELTA_PRESCALE_MASK))|
                                                          GPIO_SIGMA_DELTA_PRESCALE_SET(prescale) );

}



/******************************************************************************
 * FunctionName : set_sigma_duty_312KHz
 * Description  : 312K CONFIG EXAMPLE
 * Parameters   : uint8 duty, TARGET DUTY FOR 312K,  0-255
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
    set_sigma_duty_312KHz(uint8 duty)
{
   
    uint8 target = 0,prescale=0;
    target = (duty>128)?(256-duty):duty;
    prescale = (target==0)?0:(target-1);

    //freq = 80000 (khz) /256 /duty_target * (prescale+1)
    set_sigma_target(duty);//SET DUTY TARGET
    set_sigma_prescale(prescale);//SET CLK DIV
   
}



sigma_delta.rar

Statistics: Posted by costaud — Tue Nov 18, 2014 2:59 am

]]>